General Description
A high quality low sheen 100% acrylic finish for use on interior walls.
Uses
Suitable for interior walls and ceilings where a lower sheen than semi gloss is required, but still retaining a degree of washability. The low sheen finish tends to cover up surface imperfections and provides a softer finish for those areas subject to moderate wear.
Colours
Available in a range of bases which allow machine tinting to a wide range of popular colours.
Bases available Mid Tone Tint, Ultra Deep Tint, Dark Tint, Extra Dark Tint, Red Tint, Green Tint, Red Oxide Tint, Yellow Oxide Tint, Blue Tint, Orange Extra Tint and Yellow Extra Tint. Tinter, if added, should be vigorously and thoroughly stirred or shaken into the paint immediately after addition. This is to ensure optimum colour development of the tinter addition.
Sizes
Available in 1 litre, 2 litre, 4 litre, 10 litre and 15 litre (15L is only available in white)
Coverage
Up to 16 square metres per litre depending upon surface porosity and application method.
Application Tools
Roller, soft bristle brush or airless spray.
PROVIDE ADEQUATE VENTILATION DURING USE.
Drying Times
Touch Dry Time - 20 minutes.
Recoat Dry Time - 2 hours.
Drying times refer to normal conditions (20°C, 50% humidity). Under cooler, humid or still conditions, longer drying times may be necessary.
DO NOT USE IN TEMPERATURES BELOW 10°C OR ABOVE 30°C.
Dangerous Goods Classification
Not classified as Dangerous Goods.
Surface Preparation
Previously Painted Surfaces: Scrape off loose and flaking paint. Ensure that the remaining film is sound, sand smooth and dust down. Wash with Haymes Uni-Kleen Sugar Soap, diluted as recommended. Fill nail holes, cracks and imperfections with Haymes Unifill.Sand gloss and semi gloss surfaces thoroughly and wipe clean. Apply one coat of Haymes Acrylic Sealer Undercoat.
New Paperfaced Plasterboard: Fill any imperfections with Haymes Unifill, (not Haymes Linseed Oil Putty) sand smooth and dust down. Apply one coat of Haymes Paper Faced Plasterboard Sealer.
Fibrous or Set Plaster: Fill any imperfections with Haymes Unifill, sand smooth and dust down. Apply one coat of Haymes Sealer Binder.
Masonry, Brick, Fibro, Render or Concrete: Ensure that surface is clean. Fill imperfections with Haymes Unifill, sand smooth and dust down. Note: On asbestos cement, do not scrub or sand. Avoid dust by washing with a bleach solution then rinsing with clean water. Apply one coat of Haymes Acrylic Sealer Undercoat -alternatively apply one coat of Haymes Low Sheen Acrylic thinned with 100ml of water per litre.
New Hardboard or Timber Surfaces: Fill cracks, nail holes, etc. with Haymes Unifill, (not Haymes Linseed Oil Putty) sand smooth and dust down. Apply either two coats of Haymes Acrylic Timber Primer or one coat of Haymes Wood Primer White to avoid tannin stains bleeding through subsequent coats.
FinishingApply two coats of Haymes Low Sheen Acrylic.
Thinning and cleaning up
May be thinned with up to 100ml of water per litre for first coat on porous surfaces. Apply subsequent coat/coats unthinned. Clean equipment with water immediately after use.
Painting Conditions
Do not apply if the temperature is below 10°C. In hot weather, avoid painting in direct sunlight. Very warm or porous surfaces may be dampened with clean water prior to the application of Haymes Low Sheen Acrylic. Avoid applying in the late afternoon or in doubtful weather as frost, dew or rain is likely to impair the durability of the coating.
Storage
Protect from extremes of temperature. Store between 5°C and 30°C.
A high quality low sheen 100% acrylic finish for use on interior walls.
Uses
Suitable for interior walls and ceilings where a lower sheen than semi gloss is required, but still retaining a degree of washability. The low sheen finish tends to cover up surface imperfections and provides a softer finish for those areas subject to moderate wear.
Colours
Available in a range of bases which allow machine tinting to a wide range of popular colours.
Bases available Mid Tone Tint, Ultra Deep Tint, Dark Tint, Extra Dark Tint, Red Tint, Green Tint, Red Oxide Tint, Yellow Oxide Tint, Blue Tint, Orange Extra Tint and Yellow Extra Tint. Tinter, if added, should be vigorously and thoroughly stirred or shaken into the paint immediately after addition. This is to ensure optimum colour development of the tinter addition.
Sizes
Available in 1 litre, 2 litre, 4 litre, 10 litre and 15 litre (15L is only available in white)
Coverage
Up to 16 square metres per litre depending upon surface porosity and application method.
Application Tools
Roller, soft bristle brush or airless spray.
PROVIDE ADEQUATE VENTILATION DURING USE.
Drying Times
Touch Dry Time - 20 minutes.
Recoat Dry Time - 2 hours.
Drying times refer to normal conditions (20°C, 50% humidity). Under cooler, humid or still conditions, longer drying times may be necessary.
DO NOT USE IN TEMPERATURES BELOW 10°C OR ABOVE 30°C.
Dangerous Goods Classification
Not classified as Dangerous Goods.
Surface Preparation
Previously Painted Surfaces: Scrape off loose and flaking paint. Ensure that the remaining film is sound, sand smooth and dust down. Wash with Haymes Uni-Kleen Sugar Soap, diluted as recommended. Fill nail holes, cracks and imperfections with Haymes Unifill.Sand gloss and semi gloss surfaces thoroughly and wipe clean. Apply one coat of Haymes Acrylic Sealer Undercoat.
New Paperfaced Plasterboard: Fill any imperfections with Haymes Unifill, (not Haymes Linseed Oil Putty) sand smooth and dust down. Apply one coat of Haymes Paper Faced Plasterboard Sealer.
Fibrous or Set Plaster: Fill any imperfections with Haymes Unifill, sand smooth and dust down. Apply one coat of Haymes Sealer Binder.
Masonry, Brick, Fibro, Render or Concrete: Ensure that surface is clean. Fill imperfections with Haymes Unifill, sand smooth and dust down. Note: On asbestos cement, do not scrub or sand. Avoid dust by washing with a bleach solution then rinsing with clean water. Apply one coat of Haymes Acrylic Sealer Undercoat -alternatively apply one coat of Haymes Low Sheen Acrylic thinned with 100ml of water per litre.
New Hardboard or Timber Surfaces: Fill cracks, nail holes, etc. with Haymes Unifill, (not Haymes Linseed Oil Putty) sand smooth and dust down. Apply either two coats of Haymes Acrylic Timber Primer or one coat of Haymes Wood Primer White to avoid tannin stains bleeding through subsequent coats.
FinishingApply two coats of Haymes Low Sheen Acrylic.
Thinning and cleaning up
May be thinned with up to 100ml of water per litre for first coat on porous surfaces. Apply subsequent coat/coats unthinned. Clean equipment with water immediately after use.
Painting Conditions
Do not apply if the temperature is below 10°C. In hot weather, avoid painting in direct sunlight. Very warm or porous surfaces may be dampened with clean water prior to the application of Haymes Low Sheen Acrylic. Avoid applying in the late afternoon or in doubtful weather as frost, dew or rain is likely to impair the durability of the coating.
Storage
Protect from extremes of temperature. Store between 5°C and 30°C.